[Nov 03, 2022] Today Updated NACE-CIP2-001 Exam Dumps Actual Questions
NACE-CIP2-001 exam dumps with real NACE questions and answers
NEW QUESTION 52
Application of Thermal Spray Coatings requires:
- A. No particular skills
- B. The same skills as liquid coatings
- C. Specialized skills supported by training and experience
- D. The same skills as welding
Answer: C
NEW QUESTION 53
Centrifugal blast cleaning requires:
- A. Very large nozzles
- B. Well maintained blast wheels
- C. The use of single use abrasives
- D. A large volume of air to propel the abrasive
Answer: B
NEW QUESTION 54
A reinforced coating is
- A. more resistant to movement, abrasion, and impact than a non-reinforced coating.
- B. less resistant to movement, abrasion, and impact than a non-reinforced coating.
- C. equally resistant to movement and impact as a non-reinforced coating.
- D. equally resistant to abrasion and impact as a non-reinforced coating.
Answer: A
NEW QUESTION 55
On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?
- A. Heat-shrink sleeves
- B. Concrete
- C. Liquid epoxies
- D. Coal Tar Enamel
Answer: C
NEW QUESTION 56
The main reason dehumidification is used during coating operations is to
- A. reduce the possibility of missing the recoat window.
- B. allow the contractor to guarantee the completion date.
- C. control the environment
- D. avoid repetitive blasting/coating operations.
Answer: C
NEW QUESTION 57
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Review the standard with the Contractor and re-inspect the floor
- B. Call your supervisor
- C. Shut the job down
- D. Request that the Contractor re-blast the floor
Answer: A
NEW QUESTION 58
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. False
- B. True
Answer: A
NEW QUESTION 59
Thermal Spray coatings provide:
- A. Sacrificial protection
- B. Inhibitive protection
- C. Thermal protection
- D. Barrier protection
Answer: A
NEW QUESTION 60
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and submit the reports without any further action
- B. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Correct the errors yourself and suggest the Level 1 inspector be replaced
Answer: B
NEW QUESTION 61
Generally for safety considerations, waterjetting hose connections use
- A. a long wand.
- B. an oil/water separator.
- C. filters.
- D. a whip-lock device.
Answer: D
NEW QUESTION 62
The Concrete Repair Institute's comparators can be used to assess:
- A. Compressive and tensile strength prior to coating
- B. Surface cleanliness prior to coating
- C. Contamination levels prior to coating
- D. Surface profile prior to coating
Answer: D
NEW QUESTION 63
Measuring methyl ethyl ketone (MEK) resistance of ethyl silicate inorganic zinc-rich primers by solvent rub requires
- A. 35 single rubs with a saturated cloth.
- B. 50 double rubs with a saturated cloth.
- C. 25 double rubs with a saturated cloth.
- D. 25 single rubs with a saturated cloth.
Answer: B
NEW QUESTION 64
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. False
- B. True
Answer: A
NEW QUESTION 65
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by acid etching
- C. SP 1 followed by SP 2
- D. SP 1 followed by SP 3
Answer: C
NEW QUESTION 66
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Stop the job
- B. Advise the Owner and write a Non-Conformance report
- C. Require the Applicator to remove the coating
- D. Ignore the situation
Answer: C
NEW QUESTION 67
When ASIN D 3363 is specified the Inspector must:
- A. Record the two end points identified in the standard
- B. Record the percentage of failure
- C. Record the highest value attained
- D. Use the correct solvent
Answer: A
NEW QUESTION 68
Surface preparation of concrete is performed using:
- A. Methods that are exactly the same as steel
- B. Methods that are completely different to steel
- C. Methods that have been modified for concrete
- D. Methods that are the same as wood
Answer: C
NEW QUESTION 69
In the event of a conflict between the Product Data Sheet and the Specification:
- A. It is up to the Inspector to decide which one to follow
- B. The Product Data Sheet prevails
- C. The Specification prevails
- D. It is up to the Applicator to decide which one to follow
Answer: C
NEW QUESTION 70
The primary purpose of Fireproofing coatings are to provide:
- A. Temporary protection for the structure
- B. Explosion resistance
- C. Preferential fuel for the fire
- D. fire extinguishing characteristics
Answer: A
NEW QUESTION 71
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Stoning
- B. High-pressure water washing
- C. Acid etching
- D. Sacking
Answer: D
NEW QUESTION 72
Pre-cleaning of work pieces will NOT remove
- A. mill scale.
- B. snow, ice or water.
- C. oil or grease.
- D. dirt.
Answer: A
NEW QUESTION 73
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Give them as much advance notice as possible about upcoming changes
- B. Make sure they are the center of attention in all site meetings
- C. Challenge their value to the team and try to get them out of their comfort zone
- D. Implement immediate to get them motivated
Answer: A
NEW QUESTION 74
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. 3-Layet Polyethylene (PE)
- B. 2-Layet Polyethylene (PE)
- C. Concrete
- D. Coal Tar Enamel
Answer: C
NEW QUESTION 75
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Check to See if the dehumidification equipment is operating correctly
- B. Call your supervisor
- C. Advise the coating applicator supervisor of your readings
- D. Document the readings at the end of the shift
Answer: C
NEW QUESTION 76
......
Exam Sure Pass NACE Certification with NACE-CIP2-001 exam questions: https://prepcram.pass4guide.com/NACE-CIP2-001-dumps-questions.html