Free Sample Questions to Practice NCSC-Level-1 Certification Test Engine [May-2022]
2022 Valid NCSC-Level-1 Real Exam Questions, practice Nutanix SE Academy
NEW QUESTION 20
A consultant needs to review a customer's switch port configuration to identify any issues. Other customer requirements are as follows:
* Leverage LACP
* Native VLAN will not be used
* Use Multiple Upstream switches
* Use VLANs 20-25 and 30
* LACP Fallback has been Enabled
* vPC or MLAG has been configured
What must be included in a configuration in order to meet these requirements?
- A. Native VLAN set to default
Ports in access mode to allow all necessary VLANs - B. Native VLAN set to default
Ports trucked to allow all necessary VLANs - C. Native VLAN set to 30
Ports in access mode to allow all necessary VLANs - D. Native VLAN set to 30
Ports Trunked to allow all necessary VLANs
Answer: B
NEW QUESTION 21
During a six-node cluster deployment, one node fails to image successfully and Foundation is unable to automatically configure the cluster. The consultant decides to manually complete cluster formation with the successful nodes, then expand the cluster with the remaining unconfigured node.
Which command should be used to begin the process?
- A. cluster status
- B. cluster start
- C. cluster create
- D. cluster expand
Answer: C
NEW QUESTION 22
A consultant has deployed a new Nutanix AHV cluster with Foundation. The customer requests separating the management and production traffic in the CVM.
Which feature should the consultant configure?
- A. Micro-segmentation
- B. VLAN Tagging
- C. Network Segmentation
- D. Multi-homing
Answer: D
NEW QUESTION 23
After uploading a hypervisor ISO during the Foundation process, a consultant sees a message that the MD5 sum for the hypervisor is not found in the Whitelist file.
Which step should the consultant take next to resolve this issue?
- A. Check the hypervisor version in the Nutanix Compatibility Matrix.
- B. Download the latest hypervisor ISO whitelist file from Nutanix portal.
- C. Restart the Foundation process and upload the hypervisor again.
- D. Download the hypervisor ISO again from the vendor website.
Answer: B
NEW QUESTION 24
A consultant successfully installs the Foundation VM on a laptop and needs to ensure the VM can communicate externally.
Which two configuration changes should the consultant make next? (Choose two.)
- A. Ensure the vNIC is set to bridged adapter.
- B. Open terminal and configure via ifconfig command.
- C. Run the set_foundation_ip_address application on the VM desktop.
- D. Configure the static IP address through the desktop virtualization software.
Answer: A,C
NEW QUESTION 25
A consultant is running the Foundation VM using desktop virtualization software. No nodes are discovered.
What should the consultant verify first?
- A. NAT
- B. Bridged Adapter
- C. Internal Network
- D. Host-only Adapter
Answer: B
NEW QUESTION 26
During the Knowledge Transfer, the customer askes where to find the details about their Nutanix environment, such as IP addresses, storage containers, and configuration.
Where can the consultant find this information?
- A. Test Plan
- B. As-Built Guide
- C. Support Portal
- D. Tech Checklist
Answer: B
NEW QUESTION 27
A customer wants to use NIC teaming on an ESXi host using a vSphere Standard Switch configured with the Route based on physical NIC load load balancing option. The customer does not see the option when editing the Teaming and Failover settings for the switch.
How should the consultant resolve this issue?
- A. Add a vSphere Distributed Switch
- B. Change the load balancing option on the switch.
- C. Add another physical NIC to the team.
- D. Install a vCenter server to manage the switch
Answer: A
NEW QUESTION 28
After a recent installation using a flat switch, a consultant notices issues migrating the Nutanix nodes to the customer's network. The customer states that they are using VLANs on the production switch but not on the dedicated switch for IPMI. The customer does not require a manual configuration of the host and CVM.
What network changes need to be made to correct the issues?
- A. Use Native VLANs for the CVM and host and access mode for IPMI.
- B. Use Native VLANs for the CVM and host and trunk mode for IPMI.
- C. Use tagged VLANs for the CVM and host and access mode for IPMI.
- D. Us untagged VLANs for the CVM and host and trunk mode for IPMI.
Answer: A
NEW QUESTION 29
A customer has engaged a Nutanix consultant to deploy a cluster consisting of two NX-3460-G6 blocks. The consultant arrives at the customer site and fines the following:
* One rack with a total of 5U available
* Two ToR switches with 14 total available ports
* Dual PDUs with six available sockets
What will prevent the consultant from successfully installing the cluster?
- A. Insufficient network ports for communication.
Insufficient sockets for power allocation. - B. Insufficient network ports for communication.
Rack space may not be continuous. - C. Insufficient sockets for power allocation.
Rack space may not be continuous. - D. Insufficient rack space for block installation.
Insufficient sockets for power allocation. - E. Insufficient network ports for communication.
Insufficient sockets for power allocation.
Answer: D
NEW QUESTION 30
A consultant is planning an installation and needs to collect configuration items to be used during the install. The data needed from the customer are IP addresses, Gateway, DNS servers, and NTP Servers.
Which Cluster Deployment document must be completed with the customer?
- A. Project Plan
- B. Questionnaire
- C. Operations Guide
- D. Technical Checklist
Answer: D
NEW QUESTION 31
A Nutanix cluster has 10TB usable storage. The customer wants to create a 100GB datastore for ISO images to eliminate too much storage being consumed by unnecessary images.
Which setting should be used to accomplish this goal?
- A. From Container Advanced Settings, configure 100GB for advertised capacity.
- B. From Container Advanced Settings, turn on compression and deduplication.
- C. From Container Advanced Settings, configure 100GB for reserved capacity.
- D. From Container Advanced Settings, enable erasure coding.
Answer: A
NEW QUESTION 32
Refer to the exhibits.
A consultant is trying to test port failover on the node shown in the first exhibit. A continuous ping test is performed to the host. The consultant shuts down one of the links, after which the host ping request times out. The consultant tries to troubleshoot the issue with the customer and sees the information shown in the second exhibit on their Cisco Switches:
What is causing the issue?
- A. There is a Native VLAN mismatch on the switchport.
- B. Bad SPF+ cables are on the active interface.
- C. PortFast is not enabled on the port connected to the host.
- D. The wrong VLAN is tagged on the host.
Answer: A
NEW QUESTION 33
What is the minimum number of nodes required for a Nutanix Cluster to support Replication Factor 3 (RF3) on a storage container?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: B
NEW QUESTION 34
Which Nutanix feature creation is described in the Knowledge Transfer?
- A. REST API
- B. Data Protection Domain
- C. Calm Blueprints
- D. Self Service Portal
Answer: B
NEW QUESTION 35
A customer buys ultimate licensing and wants to use the built-in Nutanix software encryption on their new AHV cluster. The customer needs to create three storage containers and asks the consultant to complete the process as fast as possible.
In which order should the cluster be deployed?
- A. Create Cluster -> Install License Key -> Create Storage Containers -> Encrypt Cluster
- B. Create Cluster -> Create Storage Containers -> Encrypt Cluster -> Install License Key
- C. Create Cluster -> Install License Key -> Encrypt Cluster -> Create Storage Containers
- D. Create Cluster -> Encrypt Cluster -> Install License Key -> Create Storage Containers
Answer: A
NEW QUESTION 36
A customer has an ESXi Cluster with two 10GbE NICs on each node with the following requirements:
* Solution must follow Nutanix Best Practices
* Network configuration should be redundant
* A vSphere Standard Switch must be utilized
Which load balancing method should be used?
- A. Route based on physical NIC load
- B. Route based on originating port ID
- C. Route based on source MAC hash
- D. Route based on IP hash
Answer: B
NEW QUESTION 37
Where in the Support Portal is the Best Practices guide for vSphere Networking located?
- A. Solutions Documentation
- B. Software Documentation
- C. Knowledge Base
- D. Product Notices
Answer: A
NEW QUESTION 38
After finishing foundation on an AHV cluster, a consultant is preparing to plug into the customer network given the following set of requirements:
* All network traffic on trunks is tagged
* Customer is using LACP
* A native VLAN is not in use
Which set of commands should the consultant use to ensure cluster connectivity on customer equipment?
- A. change_cvm_vlan 10
ovs-vsctl set port br0 tag=10
ovs-vsctl set port br0-up bond_mode=balance-tcp - B. change_cvm_vlan 10
ovs-vsctl set port br0 tag=10
ovs-vsctl set port br0-up bond_mode=balance-slb - C. change_cvm_vlan 0
ovs-vsctl set port br0 tag=0
ovs-vsctl set port br0-up bond_mode=balance-tcp - D. change_cvm_vlan 0
ovs~vsctl set port br0 tag=0
ovs~vsctl set port br0-up bond_mode=active-backup
Answer: C
NEW QUESTION 39
A customer has a G6 AHV cluster with 4x10GbE NICs on each node and the following configuration:
* Networking is set to default
* Only two NICs are connected
The customer receives the following critical message:
The NIC is disconnected from the switch, or the switchport is failing.
What should the consultant verify to resolve the issue?
- A. The VLANs are configured correctly on the switch or tagged on the cluster.
- B. The NICs are connected for balance-slb.
- C. The other two 10GbE connections are removed from the default bond.
- D. The NICs are configured for active-backup.
Answer: D
NEW QUESTION 40
A customer wants to know the details of network validation testing.
Where can the consultant find this information?
- A. Test plan
- B. Operations Guides
- C. Handover checklist
- D. As-Built Guide
Answer: C
NEW QUESTION 41
A consultant configures a Nutanix cluster and integrates the hosts into vCenter using VMware best practices. The customer has requested that the Nutanix cluster only have a single datastore.
Upon configuring the cluster per the customer requirements, vCenter displays an alert regarding the heartbeat datastore. The consultant adds the das.ignoreInsufficientHbDatastore value = true rule. The container can be seen from each host, but the alert remains active.
What should the consultant do to resolve this issue?
- A. Turn off and then turn back on HA.
- B. Create a second container.
- C. Make sure the DRS setting is turned on.
- D. Whitelist the vCenter IP address within Prism.
Answer: A
NEW QUESTION 42
......
Genuine NCSC-Level-1 Exam Dumps Free Demo Valid QA's: https://prepcram.pass4guide.com/NCSC-Level-1-dumps-questions.html